330105-02-10-02-00 测振探头

Description

330105-02-10-02-00 测振探头

本特利Bently Nevada 330105-02-10-02-00 振动变送器集成式前置器传感器无需外部装置非隔离 PROX OUT 和 COM 端子加上同轴连接器非交互零位和跨度电位器测试输入引脚，本特利Bently Nevada 330105-02-10-02-00振动变送器用于快速验证环路信号输出不正常/信号故障电路可防止高输出或误报封装结构适用于高湿度环境(高达 100% 冷凝)。本特利Bently Nevada 330105-02-10-02-00 振动变送器主要用于离心空气压缩机或小型泵、电机或风扇的原始设备制造商 (OEM)，他们喜欢提供简单的 4 到20 mA 比例振动信号作为其机械控制系统的输入。

以上就是关于“本特利Bently Nevada 330105-02-10-02-00 振动变送器的特征”的相关介绍。本特利Bently Nevada 公司检测控制技术的重点业务涵盖了各行各业和众多应用，包括无损检测(NDT)、传感、资产状态监测、控制和仪表和辐射测量。我们正不断建立最佳实践并探索未来的解决方案，这一切的努力都是为了保证我们的客户享有质量、安全、服务和生产率。本特利Bently Nevada传感器通常安装于机器内部或表面，用于测量振动、位移、转速、压力、扭矩及能量等。本特利内华达提供多种传感器，均可满足工业环境的使用要求，部分传感器在采取本质安全栅、电磁绝缘等方法后，可安装于危险地区。

330105-02-10-02-00键相器模块

330105-02-10-02-00 改进的键相器模块是一个半高度，2 通道模块，用来为3500 框架中的监视器模块提供键相位信号。此模块接收来自电涡流传感器或电磁式传感器的输入信号，并转换此信号为数字键相位信号，该数字信号可指示何时转轴上的键相位标记通过键相位探头。每个键相模块有2个输入通道，330105-02-10-02-00 机械保护系统可安装2个键相器模块，接收4个键相位信号。

注:  键相位信号是来自旋转轴或齿轮的每转一次或每转多次的脉冲信号，提供精确的时间测量。允许330105-02-10-02-00 监测器模块和外部故障诊断设备用来测量诸如1X 幅值和相位等向量参数。

每个键相器模块可接收2 个来自涡流传感器或电磁传感器的信号。输入信号范围为-0.8V到-21.0V(非绝缘I/O 模块)和+5V到-11V(绝缘I/O 模块)。模块内可限幅，使信号不得超过此范围。无源电磁传感器要求轴转速大于200rpm(3.3Hz)。在框架前面板上，通过同轴接头，有2 个缓冲键相位输出信号。2 个缓冲键相位输出同样可在框架背面，通过欧式接头得到。前面板发光二极管 OK 指示灯: 可指示在键相器模块内检测到一个故障。

330105-02-10-02-00 测振探头

Bentley Bently Nevada 330105-02-10-02-00 Vibration transmitter Integrated pre-sensor without external device Non-isolated PROX OUT and COM terminals plus coaxial connectors Non-interactive zero and span potentiometer test input pins, Bentley Bently Nevada 330105-02-10-02-00 Vibration transmitter for rapid verification of loop signal output anomalies/signal failures The circuit prevents high output or false positives The package structure is suitable for high humidity environments (up to 100% condensation). Bentley Bently Nevada 330105-02-10-02-00 Vibration transmitters are primarily used by original equipment manufacturers (Oems) in centrifugal air compressors or small pumps, motors or fans who prefer to provide a simple 4 to 20 mA proportional vibration signal as input to their mechanical control systems.

The above is about the “Bentley Bently Nevada 330105-02-10-02-00 vibration transmitter characteristics”. Bentley Bently Nevada’s focus on inspection and control technologies spans a wide range of industries and applications, including nondestructive testing (NDT), sensing, asset condition monitoring, control and instrumentation, and radiation measurement. We are constantly establishing best practices and exploring future solutions, all in an effort to ensure quality, safety, service and productivity for our customers. Bentley Bently Nevada sensors are typically installed inside or on the surface of machines to measure vibration, displacement, speed, pressure, torque and energy. Bentley Nevada offers a wide range of sensors that meet the requirements of industrial environments, and some sensors can be installed in hazardous areas with intrinsic safety barriers, electromagnetic insulation, and other methods.

330105-02-10-02-00 Key phase module

330105-02-10-02-00 The improved key phase module is a half-height, 2-channel module designed to provide key phase signals to the monitor module in the 3500 frame. This module receives an input signal from an eddy current sensor or an electromagnetic sensor and converts this signal into a digital key phase signal that indicates when the key phase mark on the rotating shaft passes through the key phase probe. Each key phase module has 2 input channels, 330105-02-10-02-00 mechanical protection system can install 2 key phase modules, receive 4 key phase signals.

Note: The key phase signal is a pulse signal from the rotating shaft or gear once or multiple times per revolution, providing accurate time measurement. The 330105-02-10-02-00 monitor module and external fault diagnosis equipment are allowed to measure vector parameters such as 1X amplitude and phase.

Each key phaser module can receive 2 signals from eddy current sensors or electromagnetic sensors. The input signals range from -0.8V to -21.0V(uninsulated I/O modules) and +5V to -11V(insulated I/O modules). The module can be clipped so that the signal does not exceed this range. The shaft speed of a passive electromagnetic sensor must be greater than 200rpm(3.3Hz). On the front panel of the frame, through the coaxial connector, there are 2 buffer keys phase output signals. The 2 buffer key phase outputs are also available on the back of the frame via European joint. Front panel LED OK indicator: indicates that a fault has been detected in the key phaser module.