CB06560-PRD-B040SAIB-62 S600驱动系列

Description

CB06560-PRD-B040SAIB-62 S600驱动系列

该S62000-NA数字伺服放大器在与Kormogan连接时必须低电阻接地，以防止触电。放大器能产生高达900伏的高压。操作时请勿打开或触摸。未经生产厂家许可，不得对设备进行改造。它被用作电机和设备的组成部分。伺服放大器外壳外导体电压不得超过1000伏。如果装有放大器的机器不符合国家指示，该设备不得在近海应用或船舶上使用，也不得调试。这个伺服放大器一起提供大约一年的保修期。

该放大器必须在-25℃和+70℃之间的温度下运输。该设备只能保存在其原始的可回收包装中。它支持相位故障监测，短路保护和过压识别。该装置有两个模拟监控输出和两个可编程数字输出。本产品支持紧急停机功能，可以关闭安装本产品的机器。数字设备必须防止受到过大的压力。应尽可能靠近电源、扼流圈和滤波器安装在机柜接地的导电安装板上。

CB06551/CB06561/CB06560伺服放大器可能由于电机接线错误或不正确以及电源电压错误而损坏。可编程逻辑控制器监控设备的状态，以识别紧急情况。您可以通过修改产品的“设置”来安装软件。控制电缆与电源线应分开布放，间距不小于200mm。用于连接的电缆必须符合en60204标准。在DHL和fedex等合作伙伴的帮助下，我们可以将数字放大器运送到世界上任何一个地址。

CB06560-PRD-B040SAIB-62

CB06560-PRD-B040SAIB-62 S600驱动系列

This S62000-NA digital servo amplifier must be grounded with low resistance when connected from Kormogan to prevent electric shock. The amplifier is capable of producing up to 900 volts of high voltage. Do not open or touch during operation. The equipment shall not be altered without the permission of the manufacturer. It is intended to be used as a component of motors and equipment. The outer conductor of the servo amplifier housing shall not exceed 1000 volts. If the machine fitted with the amplifier does not comply with State instructions, the device shall not be used in offshore applications or on ships, nor shall it be debugged. This servo amplifier comes together to provide a guaranteed period about a year.

This amplifier must be transported at temperatures between -25℃ and +70℃. The device can only be stored in its original recyclable packaging. It supports phase fault monitoring, short circuit protection and overvoltage recognition. The unit has two analog monitoring outputs and two programmable digital outputs. This product supports an emergency stop function to shut down the machine on which it is installed. Digital equipment must be protected from excessive stress. It must be mounted as close as possible to the power supply, choke, and filter on a grounded conducting mounting plate in the cabinet.

The CB06551/CB06561/CB06560 servo amplifier may be damaged due to faulty or inappropriate motor wiring and incorrect supply voltage. The programmable logic controller monitors the status of the device to identify emergencies. You can install the software by modifying the product’s Settings. Control cables and power cables must be routed separately, at least 200 mm away from each other. The cables used for connection must comply with EN 60204. With the help of partners like DHL and fedex, we can ship digital amplifiers to any address in the world.