CFP-1804 以太网/串行背板，用于紧凑型FieldPoint

Description

CFP-1804 以太网/串行背板，用于紧凑型FieldPoint

美国国家仪器公司cFP-1804以太网/串行背板紧凑型FieldPoint

NI cFP-1804以太网/串行背板(部件编号:779490-01)可安装在面板上或普通的19英寸机架上。在使用这些安装程序之前，用户应该从模型的背面写下序列号。重要的是要记住，如果用户使用UL认可的I/O模块和紧凑型FieldPoint系统，那么他们必须将完整的系统安装在适当的额定，UL列出的NEMA或IP机箱中。为了保证最高的冷却效率，用户应该安装紧凑的FieldPoint系统，使I/O模块通风口位于顶部和底部。设备的通信速率有10mbps、100mbps和自协商速率。

4槽位cFP-1804背板能够将Compact FieldPoint I/O模块连接到高速以太网网络或RS-232串行端口(可以使用9针D-SUB男对女直连电缆连接)。要在以太网或串行网络上使用该设备，必须首先使用测量与自动化资源管理器(MAX)工具进行配置。为了将I/O模块连接到输入信号或外部负载，用户必须为背板上的每个I/O型号安装cFP-CB-x连接器块或其他连接附件。用户可以利用每个I/O模型套接字右侧的连接器套接字。用户应小心不要在给他们通电时安装或取出连接器块或其他连接附件。设备具有10BaseT和100BaseTX以太网接口，兼容IEEE802.3标准。

cFP-1804使用FieldPoint软件运行，该软件与软件包/应用程序开发环境(ADEs)兼容，如LabVIEW, LabVIEW实时模块，LabWindows/CVI, Measurement Studio或VI Logger。您选择的ADE应该在FieldPoint软件之前安装。

用户可以将美国国家仪器公司的cFP-1804背板连接到以太网、RS-232网络或两者。用户还可以通过将至少两个NI cFP-1804仪器连接到用户的PC来构建基于PC的分布式I/O和控制系统。这个设备重2磅。

CFP-1804

CFP-1804 以太网/串行背板，用于紧凑型FieldPoint

National Instruments cFP-1804 Ethernet/Serial Backplane for Compact FieldPoint

The NI cFP-1804 Ethernet/Serial Backplane (Part Number: 779490-01) is created to be mounted on a panel or in a regular 19 inch rack. Prior to utilizing these mounting procedures, the user should write down the serial number from the back of the model. It is important to keep in mind that if the user is utilizing UL Recognized I/O modules with the Compact FieldPoint system, then they must install the complete system in an appropriately rated, UL Listed NEMA or IP enclosure. To guarantee the most cooling efficiency, the user should mount the Compact FieldPoint system so that the I/O module vents are at the top and bottom. The device has communication rates of 10 Mbps, 100 Mbps, and auto-negotiated rate.

The 4-slot cFP-1804 Backplane has the capability to link Compact FieldPoint I/O modules to a high-speed Ethernet network or an RS-232 serial port (can be linked using a 9-pin D-SUB male-to-female straight-to cable). To use the device on an Ethernet or serial network, it must first be configured with the Measurement & Automation Explorer (MAX) tool. To link I/O modules to input signals or to external loads, the user must install a cFP-CB-x Connector Block or other connectivity accessory for every I/O model on the Backplane. The user can utilize the connector socket to the right side of every I/O model socket. The user should be cautious not to install or take out connector blocks or other connectivity accessories while power is brought to them. The device has a 10BaseT and 100BaseTX Ethernet network interface, and is compatible with the IEEE802.3.

The cFP-1804 is run using the FieldPoint software which is compatible with software packages/application development environments (ADEs) such as LabVIEW, LabVIEW Real-Time module, LabWindows/CVI, Measurement Studio, or VI Logger. Your ADE of choice should be installed ahead of the FieldPoint software.

The user can link the National Instruments cFP-1804 Backplane to an Ethernet network, an RS-232 network, or both. The user can additionally build a PC-based distributed I/O and control system by linking a minimum of two NI cFP-1804 instruments to the user’s PC. The device weighs 2 lbs.