IC695PNC001AF PROFINET控制器模块

Description

IC695PNC001AF PROFINET控制器模块

IC695PNC001AF是PROFINET控制器模块。该模块以前由GE智能平台公司(GE IP)生产，现在由艾默生自动化公司生产。该PROFINET控制器使RX3i CPU能够通过PROFINET网络发送和接收数据。

IC695PNC001AF兼容PACSystem RX3i CPU315或CPU320，固件版本为7.0及以上。该模块带有两(2)个RJ-45和两(2)个SFP插槽，SFP连接器单独出售。这些PROFINET端口只能分配一个IP地址。最多4个IC695PNC001可以安装在单个CPU上，并且只能安装在CPU所在的主机架上。多达六十四(64)个I/O设备可以连接到一个(1)控制器;每个网络128个I/O设备，分布在8个I/O控制器中。此外，在单个网络中最多可以安装8个I/O设备。该模块具有1 ms, 2 ms, 4 ms, 8 ms, 16 ms, 32 ms, 64 ms, 128 ms, 256 ms和512 ms的可配置数据更新时间。

IC695PNC001AF可在电源下插拔(RIUP)。不安装SFP光模块时，占用机箱单个槽位，最大电流为0.5 a;安装2个SFP光模块时，最大电流为1.2 a，其中一个SFP光模块的电流为0.35 a。在5.5 VDC时，模块最大输出1.5 A。

除了嵌入式双PROFINET端口，该模块还配备了一个微型USB连接器，用于使用命令行接口与计算机通信。它必须在0-60摄氏度的温度范围内工作。

IC695PNC001AF控制器是由GE智能平台/GE发那科PACSystems制造的PROFINET控制器，是RX3i系列的一部分。该PROFINET控制器模块有助于将RX3i PacSystems系列中的控制器连接到高速PROFINET LAN。它的一些值得注意的规范包括单个插槽，仅支持通用背板，以及PROFINET 2.2通用a类网络评级。它在5伏直流时的内部功率为1.5安培，在3.3伏直流额定电压下的内部功率为0.5安培。IC695PNC001 PROFINET控制器模块的工作温度范围为0至60摄氏度，但根据PNC001的位置和SFP的数量，可能需要更低的温度。该模块有1个微型USB接口，通过命令行接口与计算机通信。它还具有2个SFP保持架和2个RJ-45端口连接器，但SFP设备可以单独购买。

IC695PNC001AF RX3i PacSystems PROFINET控制器或PNC的主要功能包括通过使用WinLoader软件实用程序进行固件升级。控制器还具有内置的命令行接口功能，通过使用telnet或通过微型USB端口提供部分配置和直接监控。它还支持环形、星形和菊花线/链状网络拓扑。IC695PNC001 PNC的其他功能是与RX3i CPU匹配的内部时钟，用于时间戳的诊断。它还有一个重启按钮，可以手动重启PROFINET控制器，而无需启动整个系统。此PNC上的USB端口仅用于设置系统和诊断目的。

IC695PNC001AF

IC695PNC001AF PROFINET控制器模块

The IC695PNC001AF is a PROFINET controller module. This module is manufactured previously by GE Intelligent Platforms (GE IP), now by Emerson Automation. This PROFINET controller enables an RX3i CPU to send and receive data over PROFINET network.

The IC695PNC001AF is compatible for use with PACSystem RX3i CPU315 or CPU320, with firmware version 7.0 or higher. This module comes with Two (2) RJ-45 and Two (2) SFP slots with SFP connectors separately sold. Only One IP address is assigned for these PROFINET ports. Up to Four (4) IC695PNC001 can be installed along a single CPU and must located to the to the main rack only, where the CPU resides. Up to Sixty-Four (64) I/O devices can be connected to One (1) controller; 128 I/O device per network, distributed among Eight (8) I/O controllers. Additionally, up to Eight (8) I/O devices can be installed in a single network. This module has configurable data update times of 1 ms, 2 ms, 4 ms, 8 ms, 16 ms, 32 ms, 64 ms, 128 ms, 256 ms and 512 ms.

The IC695PNC001AF can be Removed and Inserted Under Power (RIUP). It occupies a single slot of the chassis and draws 0.5 A without SFP devices installed and maximum of 1.2 A maximum with Two (2) SFP devices installed where an SFP device uses 0.35 A. At 5.5 VDC, the module draws 1.5 A, maximum.

Aside from the embedded dual PROFINET ports, this module also comes with a micro USB connector that is used for communicating with a computer using Command Line Interface. It must be operated at a temperature range of 0-60 Degree Celsius.

The IC695PNC001AF controller is a PROFINET controller manufactured by GE Intelligent Platforms/GE Fanuc PACSystems as part of the RX3i series. This PROFINET controller module helps to connect the controllers in the RX3i PacSystems series to a high-speed PROFINET LAN. Some of its notable specifications include a single slot, support for only universal backplanes, and PROFINET 2.2 General Class A network ratings. It operates on an internal power of 1.5 Amps at 5 Volts DC or 0.5 Amps at a rated voltage of 3.3 Volts DC. The IC695PNC001 PROFINET controller module has an operating temperature range of 0 to 60 degrees Celsius, but lower temperatures may be needed depending on the PNC001 location and the population of SFP. This module has 1 micro USB connector for communication with the computer through the command-line interface. It also features 2 SFP cages and 2 RJ-45 port connectors, but the SFP devices can be acquired separately.

The main features of the IC695PNC001AF RX3i PacSystems PROFINET controller or PNC include firmware upgrades through the use of the WinLoader software utility. The controller also has a built-in command-line interface functionality that provides partial configuration and direct monitoring by using the telnet or through a micro USB port. It also has support for ring, star, and daisy-line/chain network topologies. Other features of the IC695PNC001 PNC are an internal clock matched with an RX3i CPU for diagnostics that are time-stamped. It also features a restart pushbutton that restarts the PROFINET controller manually without having to power cycle the whole system. The USB port on this PNC is designed for setting up the system and for diagnostic purposes only.