购买咨询热线/Phone：
邮箱/Email：
地址：Description
IS220PVIBH1A 连接器直接连接到匹配的端子板连接器以进行输出
IS220PVIBH1A 是 GE 在 Mark VIe 控制系统下开发的振动监测器 (PVIB) 包。振动监视器 (PVIB) 包以电气方式将一个或两个 I/O 以太网连接到 TVBA 振动端子板。该包包括一个处理器板、一个采集板和一个子板，这些都是所有 Mark VIe 分布式 I/O 包所共有的。
该包使用通道 1 至 8 从以下传感器类型读取振动或接近信息：前置器、集成输出加速度计（仅限通道 1-3）、Velomitor 或地震通道 9 至 12 仅支持前置器，而通道 13 可以输入键相信号类型或接近类型信号。
双 RJ45 以太网端口和 3 针电源输入用于为电池组供电。对于低于 100 Hz 的帧速率，PVIB 支持双以太网。它通过以太网支持 3.125、6.25、12.5、25、50 和 100 Hz 的帧速率。
DC-37 针连接器直接连接到匹配的端子板连接器以进行输出。LED 指示灯用于显示视觉诊断。
IS220PVIBH1A 兼容性
双 RJ45 以太网端口和 3 针电源输入用于为电池组供电。对于低于 100 Hz 的帧速率，PVIB 支持双以太网。它通过以太网支持 3.125、6.25、12.5、25、50 和 100 Hz 的帧速率。DC-37 针连接器直接连接到匹配的端子板连接器以进行输出。LED 指示灯用于显示视觉诊断。
IS220PVIBH1A安装
按照步骤安装包
固定您要使用的端子板。
将 PVIB I/O 包直接连接到端子板连接器。
使用靠近以太网端口的螺柱以机械方式固定电池组。
根据系统配置，连接一根或两根以太网线。该包可与任一端口一起使用。使用双连接时，ENET1 应连接到与 R 控制器链接的网络。
插入侧面的连接器，将电池组连接到电源。
使用 ToolboxST* 应用程序根据需要配置 I/O 包。
检查 TVBA 上的 N28 电源子板是否正确放置在 TVBA 连接器中。
IS220PVIBH1A 连接器直接连接到匹配的端子板连接器以进行输出
The IS220PVIBH1A is a vibration monitor (PVIB) package developed by GE under the Mark VIe Control System. The Vibration Monitor (PVIB) package electrically connects one or two I/O Ethernet cables to the TVBA vibration terminal board. The package includes a processor board, a capture board, and a child board, which are common to all Mark VIe distributed I/O packages.
The package uses channels 1 through 8 to read vibration or proximity information from the following sensor types: precursors, integrated output accelerometers (channels 1-3 only), Velomitor, or seismic channels 9 through 12 support precursors only, while channels 13 can input key type or proximity type signals.
The dual RJ45 Ethernet port and 3-pin power input are used to power the battery pack. For frame rates below 100 Hz, the PVIB supports dual Ethernet. It supports frame rates of 3.125, 6.25, 12.5, 25, 50, and 100 Hz over Ethernet.
The DC-37 pin connector connects directly to the matching terminal board connector for output. LED indicator is used to display visual diagnosis.
IS220PVIBH1A Compatibility
The dual RJ45 Ethernet port and 3-pin power input are used to power the battery pack. For frame rates below 100 Hz, the PVIB supports dual Ethernet. It supports frame rates of 3.125, 6.25, 12.5, 25, 50, and 100 Hz over Ethernet. The DC-37 pin connector connects directly to the matching terminal board connector for output. LED indicator is used to display visual diagnosis.
IS220PVIBH1A Installation
Follow the steps to install the package
Secure the terminal board you want to use.
Connect the PVIB I/O package directly to the terminal board connector.
The battery pack is mechanically secured using a stud near the Ethernet port.
Connect one or two Ethernet cables based on the system configuration. The package can be used with either port. When using dual connections, ENET1 should be connected to the network linked to the R controller.
Plug in the connector on the side to connect the battery pack to the power supply.
Use the ToolboxST* application to configure I/O packages as needed.
Check that the N28 power subboard on the TVBA is properly placed in the TVBA connector.
购买咨询热线/Phone：18859254943- 邮箱/Email：sales@ygdcs.com
- 地址：成都高新区天益街北巷52号附14号2层
